ReJuviSeal installs an invisible, protective coating on stone surfaces that repels oil, water and stains. This product has the ability to be renewed with ReJuviClean®, a cleaner and protective treatment. This product is designed for high-performance building restoration and preservation applications. DETAILED DESCRIPTIONThis product is a clear, penetrating sealer for stone surfaces that will not alter the appearance of the material. This product utilizes proprietary, UV-resistant fluorochemistry that will outlast other water and oil repellants. It is designed to penetrate the surface and react with the silica within the stone, expanding and filling cracks and crevices in the material to create a long-lasting repellency to oil, water and stains. It can be applied to surfaces that have been previously treated with inferior silane or siloxane water-repellant products. In independent tests, ReJuviSeal proved to repel standing oil from penetrating the surface of concrete for over one month. After use, the protective coating is easily rejuvenated using Presto’s ReJuviClean.PRODUCT DETAILSAdvantages
Intended UseCan be used on concrete, masonry and stone surfaces.Horizontal or VerticalCan be used on either horizontal or vertical surfaces.
Complete all caulking and surrounding construction substrate applications prior to using this product. Newly installed stone or grout must be allowed to cure before application. Protect against personal contact with this and all chemical products. Always test on a small, inconspicuous area prior to application. Ensure the stone is completely clean and free from all dirt, staining and biological growth using any of Presto’s stone cleaning products. Make sure to thoroughly rinse the material to ensure no product is left behind on the surface prior to sealing. Any cleaning product left on the surface can interfere with the protective coating. Protect any unintended areas. Never apply to a damp or wet surface. Do not apply in below freezing temperatures. Use a low-pressure sprayer, roller, brush, sponge or lambs wool applicator. Product may also be back rolled. Do not dilute; apply full strength. Apply product to create an even coat on the surface. Allow product to saturate surface. Do not allow product to pool on the surface and dry, or protection will be uneven and a residue may form. Remove excess material with a rag or towel. A second coat may be needed for porous, absorbent surfaces or for superior protection. Subsequent coats should be applied in the same manner as the first while the initial application is drying. Never apply a second coat if two coats were not tested and approved prior to use. Protection will begin immediately after sealant dries on the surface. Cure time for maximum water and stain protection is 24-72 hours. Protect surface from contact with water for at least 48 hours. Application rates, concentration, temperature and humidity can impact dry and cure time. Use towels or rags to polish the surface. For parking garages: Surfaces must be thoroughly cleaned prior to application of ReJuviSeal. It will protect concrete from vehicle stains, such as motor oil and transmission fluid. With proper use, regular cleaning can be performed with a street cleaner, pressure washer, oil absorbers and other standard techniques. In many instances, a combination of different stone cleaning products is necessary for various stone surfaces depending on their level and type of staining. Presto offers a complete line of stone cleaning products for all situations, including:
CleanupClean tools and equipment with water. Clean any area that may have overspray with one of the following products:
Protected Surface Maintenance InstructionsFor light-cleaning and rejuvenating benefits, Presto’s ReJuviClean® can be used. Or for ongoing maintenance of the protected surface, we recommend the use of deionized water. Apply to the surface and use a soft brush to loosen any stubborn soils from the surface. For exterior vertical surfaces on a building that is being properly cleaned using Presto products, we recommend cleaning the surface every 1-2 years for horizontal surfaces, and every 2-3 years for vertical surfaces, in order to maintain a clean appearance and preserve the previous restoration. High pressure is not needed and may damage the surface coating or weaken its performance. This maintenance cleaning is not mandatory to ensure the coating will last as stated in the warranty and is only a suggestion.The information provided by Presto for the safe and effective use of this product, and all of our products, is believed to be good and accurate. However, due to the many different possible applications of this product, careful considerations should be made when selecting its suitability for each surface. The information provided should never be substituted for individual testing to ensure the product’s compatibility with each surface intended for use. The purchaser shall assume all responsibility for determining the suitability of this product. When used as intended, this product will perform as stated. No other warranty can be made for this product, verbally or written. Presto warrants this product to be free from defects. In the event this product is found to be defective, we will provide a sufficient amount of product to replace the defective product. View Our Precast & Concrete Before & After PicturesView our Stone Restoration Pictures Featuring projects that utilized our many products for their building's restoration, maintenance or cleaning project. After cleaning or sealing stone surfaces, the glass windows and metal frames almost always need to be cleaned, and many times window spots and stains will need to be removed as well. View our glass and metal products that compliment our stone restoration and protection products. Don't Forget the Glass & Metal Surfaces
|
View All Products > Architectural Precast, Concrete, Brick & Block Restoration Products > Stone Protection Products >